1 Introduction to Installing Oracle Clusterware and Oracle Real Application Clusters

Cluster Verification Utility

Cluster Verification Utility (CVU) is provided with Oracle Database 10g Release 2 (10.2) with Real Application Clusters. The purpose of CVU is to enable you or your hardware vendors to verify during setup and configuration that all components required for a successful installation of an Oracle RAC database are installed and configured correctly, and to provide you with ongoing assistance any time you need to make changes to your Oracle RAC cluster. You are provided with commands to use CVU to verify completion of tasks in this guide.

There are two types of CVU commands:

• Stage Commands are CVU commands used to test system setup and readiness for successful software installation, database creation, or configuration change steps. These commands are also used to validate successful completion of specific cluster configuration steps.

• Component Commands are CVU commands used to check individual cluster components, and determine their state.

This guide provides stage and component CVU commands where appropriate to assist you with cluster verification.

Hardware Requirements for Oracle Database 10g Real Application Clusters

Each node in a cluster requires the following hardware:

• External shared disks for storing Oracle Clusterware and database files.

  The disk configuration options available to you are described in Chapter 3, "Storage Pre-Installation Tasks". Review these options before you decide which storage option to use in your Oracle RAC environment. However, note that when Database Configuration Assistant (DBCA) configures automatic disk backup, it uses a database recovery area which must be shared. The database files and recovery files do not necessarily have to be located on the same type of storage.

• One private internet protocol (IP) address for each node to serve as the private interconnect. The following must be true for each private IP address:

  • It must be separate from the public network

  • It must be accessible on the same network interface on each node

  • It must have a unique address on each node

  The private interconnect is used for inter-node communication by both Oracle Clusterware and Oracle RAC. If the private address is available from a network name server (DNS), then you can use that name. Otherwise, the private IP address must be available in each node's C:\WINNT\system32\drivers\etc\hosts file.

  During Oracle Clusterware installation, the information you enter as the private IP address determines which private interconnects are used by Oracle RAC database instances. If you define more than one interconnect, then they must all be in an up state, just as if their IP addresses were specified in the initialization parameter, CLUSTER_INTERCONNECTS. Oracle RAC does not fail over between cluster interconnects; if one is down then the instances using them will not start.

  Oracle recommends that you use a logical Internet Protocol (IP) address that is available across all private networks, and that you take advantage of any available third party network interface cards that provide bonding to enable network failover by configuring them according to the vendor's instructions.

• One public IP address for each node, to be used as the Virtual IP (VIP) address for client connections and for connection failover The name associated with the VIP must be different from the default host name.

  This VIP must be associated with the same interface name on every node that is part of your cluster. In addition, the IP addresses that you use for all of the nodes that are part of a cluster must be from the same subnet. If you have a domain name server (DNS), then register the host names for the VIP with DNS. The Virtual IP address should not be in use at the time of the installation, because this is a Virtual IP address that Oracle manages.

• One public fixed hostname address for each node, typically assigned by the system administrator during operating system installation. If you have a DNS, then register both the fixed IP and the VIP address with DNS. If you do not have DNS, then you must make sure that the public IP and VIP addresses for all nodes are in each node's host file.

Software Requirements for Oracle Database 10g Real Application Clusters

Each node in a cluster requires a supported interconnect software protocol to support Cache Fusion, and to support Oracle Clusterware polling. Your interconnect must be certified by Oracle for your platform. You should also have a Web browser, both to enable Oracle Enterprise Manager, and to view online documentation.

Oracle RAC databases on the same cluster must all be 64-bit or all 32-bit. Oracle does not support combining 64-bit Oracle RAC databases and 32-bit Oracle RAC databases on the same cluster.

Pre-Installation Overview for Oracle Clusterware and Oracle Real Application Clusters

The pre-installation procedures in Part II explain how to verify user equivalence, perform network connectivity tests, as well as how to set directory and file permissions. Complete all of the pre-installation procedures and verify that your system meets all of the pre-installation requirements before proceeding to the install phase.

Installation Overview for Oracle Clusterware and Oracle Real Application Clusters

Oracle Database 10g Real Application Clusters installation is a two-phase installation. In phase one, use Oracle Universal Installer (OUI) to install Oracle Clusterware as described in Chapter 4, "Installing Oracle Clusterware on Windows-Based Systems". In phase two, install the database software using OUI. Oracle Clusterware installation starts Oracle Clusterware processes in preparation for installing Oracle Database 10g. In phase two, you install Oracle database software for use with single-instance or with Oracle RAC databases. To install the database software for use with single-instance databases in phase two, refer to the Microsoft Windows installation guides. To install the database software with Oracle RAC in phase two, use OUI to install Oracle RAC software as described in Chapter 5, "Installing Oracle Database 10g with Oracle Real Application Clusters". Note that the Oracle home that you use in phase one is a home for Oracle Clusterware software which must be different from the Oracle home that you use in phase two.

If OUI detects a previous version of Oracle Database, then OUI starts Database Upgrade Assistant (DBUA) to upgrade your database to Oracle Database 10g Release 2 (10.2). In addition, DBUA displays a Service Configuration page for configuring services in your Oracle RAC database.

After the database software installation completes, OUI starts the Oracle assistants, such as Database Configuration Assistant (DBCA), to configure your environment and create your database. For an Oracle RAC database, you can later use DBCA Instance Management feature to add or modify services and instances as described in Chapter 6, "Creating Oracle RAC Databases with the Database Configuration Assistant".

Post-Installation Overview for Oracle Database 10g Real Application Clusters

After you create your database, download and install the most recent patch sets for your Oracle Database 10g version as described in the single-instance installation manual or in Chapter 7, "Oracle Real Application Clusters Post-Installation Procedures". If you are using other Oracle products with your Oracle RAC database, then you must also configure them.

You must also perform several post-installation configuration tasks to use certain Oracle Database 10g products such as Sample Schema, Oracle Net Services, or Oracle Messaging Gateway. You must also configure Oracle pre-compilers for your operating system and if desired, configure Oracle Advanced Security.

Use the Companion media to install additional Oracle Database 10g software that may improve performance or extend database capabilities, for example, Oracle JVM, Oracle interMedia or Oracle Text.

Overview of Automatic Storage Management

Oracle recommends using Automatic Storage Management (ASM) or a cluster file system with Oracle Managed Files (OMF) for database storage. This section provides an overview of ASM.

Note that Oracle RAC installations using Oracle Database Standard Edition must use ASM for database file storage.

You can use ASM to simplify the administration of Oracle database files. Instead of having to manage potentially thousands of database files, using ASM, you need to manage only a small number of disk groups. A disk group is a set of disk devices that ASM manages as a single logical unit. You can define a particular disk group as the default disk group for a database, and Oracle will automatically allocate storage for, create, or delete, the files associated with the appropriate database object. When administering the database, you need only refer to database objects by name, rather than by file name.

When using ASM with a single Oracle home for database instances on a node, the ASM instance can run from that same home. If you are using ASM with Oracle database instances from multiple database homes on the same node, then Oracle recommends that you run the ASM instance from an Oracle home that is distinct from the database homes. In addition, the ASM home should be installed on every cluster node. Following this recommendation prevents the accidental removal of ASM instances that are in use by databases from other homes during the de-installation of a database's Oracle home.

Benefits of Automatic Storage Management

ASM provides many of the same benefits as storage technologies such as a redundant array of independent disks (RAID) or logical volume managers (LVMs). Like these technologies, ASM enables you to create a single disk group from a collection of individual disk devices. It balances input and output (I/O) loads to the disk group across all of the devices in the disk group. It also implements striping and mirroring to improve I/O performance and data reliability.

However, unlike RAID or LVMs, ASM implements striping and mirroring at the file level. This implementation enables you to specify different storage attributes for individual files in the same disk group.

Disk Groups and Failure Groups

A disk group can include up to 10,000 disk devices. Each disk device can be an individual physical disk, a multiple disk device such as a RAID storage array or logical volume, or even a partition on a physical disk. However, in most cases, disk groups consist of one or more individual physical disks. To enable ASM to balance I/O and storage appropriately within the disk group, all devices in the disk group should have similar, if not identical, storage capacity and performance.

When you add a device to a disk group, you can specify a failure group for that device. Failure groups define ASM disks that share a common potential failure mechanism. An example of a failure group is a set of SCSI disks sharing the same SCSI controller. Failure groups are used to determine which ASM disks to use for storing redundant copies of data. For example, if two-way mirroring is specified for a file, ASM automatically stores redundant copies of file extents in separate failure groups.

Redundancy Levels

ASM provides three levels of mirroring, called redundancy levels, that you can specify when creating a disk group. The redundancy levels are:

• External redundancy

  In disk groups created with external redundancy, the contents of the disk group are not mirrored by ASM. You might choose this redundancy level when:

  • The disk group contains devices, such as RAID devices, that provide their own data protection

  • Your use of the database does not require uninterrupted access to data, for example, in a development environment where you have a suitable back-up strategy

• Normal redundancy

  In disk groups created with normal redundancy, the contents of the disk group are two-way mirrored by default, except the control file, which is three-way mirrored. However, you can choose to create certain files that are not mirrored or that are three-way mirrored in a disk group with normal redundancy. To create a disk group with normal redundancy, you must specify at least two failure groups (a minimum of two devices).

  The effective disk space of a disk group that uses normal redundancy is half the total disk space of all of its devices.

• High redundancy

  In disk groups created with high redundancy, the contents of the disk group all three-way mirrored. To create a disk group with high redundancy, you must specify at least three failure groups (a minimum of three devices).

  The effective disk space of a disk group that uses high redundancy is one-third of the total disk space of all of its devices.

ASM and Installation Types

The type and number of disk groups that you can create when installing Oracle software depends on the type of database you choose to create during the installation, as follows:

• Preconfigured database

  If you choose to create the default preconfigured database that uses ASM, then OUI prompts you for the disk device names it will use to create a disk group with the default name of DATA.

• Advanced database

  If you choose to create an advanced database that uses ASM, then you can create one or more disk groups. These disk groups can use one or more devices. For each disk group, you can specify the redundancy level that suits your requirements.

The following table lists the total disk space required in all disk group devices for a typical preconfigured database, depending on the redundancy level you choose to use for the disk group:

You can also run OUI and to install ASM only without the database and Oracle RAC software.

Shared Storage for Database Recovery Area

When you configure a database recovery area in an Oracle RAC environment, the database recovery area must be on shared storage. When Database Configuration Assistant (DBCA) configures automatic disk backup, it uses a database recovery area that must be shared.

If the database files are stored on a cluster file system, then the recovery area can also be shared through the cluster file system.

If the database files are stored on an Automatic Storage Management (ASM) disk group, then the recovery area can also be shared through ASM.

If the database files are stored on raw devices, then you must use either a cluster file system or ASM for the recovery area.

Oracle Clusterware

You must provide OUI with the names of the nodes on which you want to install Oracle Clusterware. The Oracle Clusterware home can be either shared by all nodes, or private to each node, depending on your responses when you run OUI. The home that you select for Oracle Clusterware must be different from the Oracle RAC enabled Oracle home.

When third-party vendor clusterware is present, Oracle Clusterware may interact with the third-party vendor clusterware. For Oracle Database 10g on Windows, Oracle Clusterware coexists with but does not interact with previous Oracle clusterware versions.

The Installed Real Application Clusters Components

All instances in Oracle RAC environments share the control file, server parameter file, redo log files, and all datafiles. These files reside on a shared cluster file system or on shared disks. Either of these types of file configurations are accessed by all the cluster database instances. Each instance also has its own set of redo log files. During failures, shared access to redo log files enables surviving instances to perform recovery.

Cloning Oracle Clusterware Homes

This section outlines the procedure required to clone an existing Oracle Clusterware home from one node (the source node) to one or more other nodes (the target nodes). The procedure consists of the following tasks:

1. Ensure that Oracle Clusterware software is installed successfully on the source node. You can use CVU for this task.

2. As a Windows administrative user, create a zip file of the Oracle Clusterware home directory, selecting the "Save full path info" option.

3. On a selected target node, create an Oracle Clusterware home directory, and copy the Oracle Clusterware zip file from the source node to the target node Oracle Clusterware home.

4. As a Windows administrative user, extract the zip file contents, selecting the "Use folder names" option.

5. Repeat steps 3 and 4 on each of the other target nodes, unless the Oracle Clusterware home is on a shared storage device.

6. On each of the target nodes, run OUI in clone mode as described in Oracle Universal Installer and OPatch User's Guide.

7. Complete the post-cloning installation instructions as described in Oracle Universal Installer and OPatch User's Guide.

Cloning Real Application Clusters Homes

Complete the following tasks to Clone an Oracle RAC database image on multiple nodes:

1. Ensure that Oracle Database with Oracle RAC software is installed successfully on the source node.

2. Create a zip file of the Oracle home directory, selecting the "Save full path info" option.

3. On a selected target node, create an Oracle home directory, and copy the Oracle Clusterware zip file from the source node to the target node Oracle Clusterware home.

4. Extract the zip file contents, selecting the "Use folder names" option.

5. Repeat steps 3 and 4 on each of the other target nodes, unless the Oracle home is on a shared storage device.

6. On each of the target nodes, run OUI in clone mode as described in Oracle Universal Installer and OPatch User's Guide.

7. Complete the post-cloning installation instructions as described in Oracle Universal Installer and OPatch User's Guide.

8. Run the configuration assistant NetCA on a local node of the cluster, and provide a list when prompted of all nodes that are part of the cluster.

9. Run the configuration assistant DBCA to create the database.