FLASHBACK DATABASE

Purpose

Use the FLASHBACK DATABASE statement to return the database to a past time or system change number (SCN). This statement provides a fast alternative to performing incomplete database recovery.

Following a FLASHBACK DATABASE operation, in order to have write access to the flashed back database, you must reopen it with an ALTER DATABASE OPEN RESETLOGS statement.

See Also:

Oracle Database Backup and Recovery Basics for more information on FLASHBACK DATABASE

Prerequisites

You must have the SYSDBA system privilege. A flash recovery area must have been prepared for the database. The database must have been put in FLASHBACK mode with an ALTER DATABASE FLASHBACK ON statement unless you are flashing the database back to a guaranteed restore point. The database must be mounted but not open.

See Also:

Oracle Database Backup and Recovery Advanced User's Guide and the ALTER DATABASE ... flashback_mode_clause for information on putting the database in FLASHBACK mode
CREATE RESTORE POINT for information on restore points and guaranteed restore points

Syntax

flashback_database::=

Description of the illustration flashback_database.gif

Semantics

When you issue a FLASHBACK DATABASE statement, Oracle Database first verifies that all required archived and online redo logs are available. If they are available, then it reverts all currently online datafiles in the database to the SCN or time specified in this statement.

The amount of Flashback data retained in the database is controlled by the DB_FLASHBACK_RETENTION_TARGET initialization parameter and the size of the flash recovery area. You can determine how far back you can Flashback the database by querying the V$FLASHBACK_DATABASE_LOG view.
If insufficient data remains in the database to perform the Flashback, then you can use standard recovery procedures to recover the database to a past point in time.
If insufficient data remains for a set of datafiles, then the database returns an error. In this case, you can take those datafiles offline and reissue the statement to revert the remainder of the database. You can then attempt to recover the offline datafiles using standard recovery procedures.

See Also:

Oracle Database Backup and Recovery Advanced User's Guide for more information on recovering datafiles

STANDBY

Specify STANDBY to revert the standby database to an earlier SCN or time. If the database is not a standby database, then the database returns an error. If you omit this clause, then database can be either a primary or a standby database.

See Also:

Oracle Data Guard Concepts and Administration for information on how you can use FLASHBACK DATABASE on a standby database to achieve different delays

TO SCN Clause

Specify a system change number (SCN):

TO SCN reverts the database back to its state at the specified SCN.
TO BEFORE SCN reverts the database back to its state at the system change number just preceding the specified SCN.

You can determine the current SCN by querying the CURRENT_SCN column of the V$DATABASE view. This in turn lets you save the SCN to a spool file, for example, before running a high-risk batch job.

TO TIMESTAMP Clause

Specify a valid datetime expression.

TO TIMESTAMP reverts the database back to its state at the specified timestamp.
TO BEFORE TIMESTAMP reverts the database back to its state one second before the specified timestamp.

You can represent the timestamp as an offset from a determinate value, such as SYSDATE, or as an absolute system timestamp.

TO RESTORE POINT Clause

Specify this clause to flash back the database to the specified restore point. If you have not enabled flashback database, this is the only clause you can specify in this FLASHBACK DATABASE statement. If the database is not in FLASHBACK mode, as described in the "Prerequisites" section above, this is the only clause you can specify for this statement.

RESETLOGS

Specify TO BEFORE RESETLOGS to flash the database back to just before the last resetlogs operation (ALTER DATABASE OPEN RESETLOGS).

See Also:

Oracle Database Backup and Recovery Basics for more information about this clause

Examples

Assuming that you have prepared a flash recovery area for the database and enabled media recovery, enable database FLASHBACK mode and open the database with the following statements:

STARTUP MOUNT 
ALTER DATABASE FLASHBACK ON;
ALTER DATABASE OPEN;

With your database open for at least a day, you can flash back the database one day with the following statements:

SHUTDOWN DATABASE
STARTUP MOUNT 
FLASHBACK DATABASE TO TIMESTAMP SYSDATE-1;